CADDX NX-6 Manual de instalación descargar pdf (Pagina 30)

GE Security

Programming the NX-6 control panel via LCD keypad

ENTERING THE PROGRAM MODE

To enter the program mode, press [*]-[8]. The LCD screen will now prompt you for the

programming code. Next, enter the “Go To Program Code” (FACTORY DEFAULT IS

9713). If the “Go To Program Code” is valid, the LCD screen will prompt you for the

device address you wish to program. You are now in the program mode, ready to select

the module to be programmed.

Note: it is impossible to enter program mode if any partition - or the system - is armed.

SELECTING THE MODULE TO PROGRAM

Since all the modules connected to the NX-6 are programmed through the keypad, the

module you are programming should be the first entry. To program the NX-6 Control

Panel, enter [0]-[#]. The [0] is the module number of the control panel and the [#] is the

entry key. Other module entry numbers can be found in the corresponding manuals.

PROGRAMMING A LOCATION

Note: Before programming the panel, the correct country code must be set in loc. 213

Once you have entered the number of the module to be programmed, the LCD screen will

prompt you for a location number. Any location can be accessed by directly entering the

desired programming location, followed by the crosshatch (pound) [#] key. If the location

you enter is valid, the top line of the LCD screen will display the location number on the

left and the segment number on the right. The bottom line of the display will show the

current data. This data will be displayed and entered according to the type of data used

(numerical, binary, or character data). Follow the instructions below for each type of data.

NUMERICAL DATA: The top line of the display will show the current location number on

the left and the segment number on the right. The data will be displayed on the bottom

line. The hex equivalent will be shown in parenthesis. To change the data in the current

location, enter the number followed by [*]. The data will be entered and the segment will

be incremented by 1. The data for this segment will now be displayed. Continue this

process until the last segment is programmed. When you reach the last segment, the

keypad will prompt you for the next location. If you wish to exit this location before the last

segment is reached, press the [#] key. This keypress will not save the changes made to

current segment, but it will exit the location. To proceed to the next location, press the

[Police] key. To return to the previous location, press the [Fire] key. To re-enter the last

location, press the [Medic] key.

BINARY DATA: The top line of the display will show the current location number on the

left and the segment number on the right. The data will be displayed on the bottom line

with the numbers 1-8 in the first 8 characters. If the number appears, this binary switch is

on. If minuses sign (-) appears where the number should be, this switch is off. Toggle the

numbers on or off, using the corresponding number digit (1 to toggle 1, 8 to toggle 8).

When the numbers are in the desired state, press the [*] key. The data will be entered

and the segment will be incremented by 1. The data for this segment will now be

displayed. Continue this process until the last segment is programmed. When you reach

the last segment, the keypad will prompt you for the next location. If you wish to exit this

location before the last segment is reached, press the [#] key. This keypress will not save

the changes made to current segment, but will exit the location. To proceed to the next

location, press the [Police] key. To return to the previous location, press the [Fire] key. To

re-enter the last location, press the [Medic] key.

NX-6-EUR Installation manual Page 30 23/12/04

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 103 104

Comentarios a estos manuales

Sin comentarios

CADDX NX-6 Manual de instalación Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad CADDX NX-6