CADDX NX-8e Especificaciones descargar pdf (Pagina 27)

NX-8E CONTROL

LOCATION 47 - AUXILIARY OUTPUT #1, EVENT AND TIME (2 segments, numerical data)

Segment 1: Use Table XI-1 on page 25 to select the event that will activate Auxiliary Output 1.

Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in

Segment 1, Location 46). Programming a "0" makes the output follow the event.

LOCATION 48 - AUXILIARY OUTPUT #2, EVENT AND TIME (2 segments, numerical data)

Segment 1: Use Table XI-1 on page 25 to select the event that will activate Auxiliary Output 2.

Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in

Segment 2, Location 46). Programming a "0" makes the output follow the event.

LOCATION 49- AUXILIARY OUTPUT #3, EVENT AND TIME (2 segments, numerical data)

Segment 1: Use Table XI-1 on page 25 to select the event that will activate Auxiliary Output 3.

Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in

Segment 3, Location 46). Programming a "0" makes the output follow the event.

LOCATION 50- AUXILIARY OUTPUT #4, EVENT AND TIME (2 segments, numerical data)

Segment 1: Use Table XI-1 on page 25 to select the event that will activate Auxiliary Output 4. .

Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in

Segment 4, Location 46). Programming a "0" makes the output follow the event.

Table XI-1 AUXILIARY OUTPUT EVENT SELECTION

DATA EVENT DATA EVENT DATA EVENT

Burglary Alarm 19 Exit 38 Download In Process



/ Fire Alarm 20 Entry or Exit 39 Smoke Power



/ 24 Hour Alarm 21 Armed State 40 Short Circuit (Over-current)



/ Trouble Alarm 22 Disarmed State 41 Box Tamper



/ Tamper Alarm 23 Ready 42 Siren Tamper

5 Yelping Siren (Burglary) 24 Not Ready 43 Any Open

6 Temporal Siren (Fire) 25 Fire 44 Any Short

7 Any Siren 26 Fire Trouble 45 Any Fault (Open/ Short on Non-Fire Zone)

8 Any Bypass 27 Chime 46



/ Any Alarm

9 AC Fail 28



/ Expander Trouble 47 Beeping Keypad

10 Low Battery 29 Dynamic Battery Test Time 48



/ Code Entry (See note below)



/ Duress 30 Open Period 49

˜ /

Key FOB Function 1



/ Aux 1 Keypad Zone 31 Closed Period 50

˜ /

Key FOB Function 2



/ Aux 2 Keypad Zone 32 Listen-In 51 Always ON



/ Panic Keypad Zone 33 Line Seizure 52 Alarm Flash

15 Keypad Tamper 34 Ground Start 53 Armed Away



/ Autotest 35 Fail To Communicate 54 Armed Stay

17 Alarm Memory 36 Telephone Line Fault 55 Aux Comm Fail

18 Entry 37 Program Mode 56 (CP-01) Progress Annunciation

˜ Events 49 & 50 require one or more of the following to operate: NX-408E, NX-416E, NX-448E wireless

receivers, or NX-1700E card reader.

/ If set to follow condition, these events will be 1 second.

Notes: When Event 48 is programmed, it is possible to program a user code's authorization to select which output(s)

a particular code will activate. When LED 8 is on for an authorization, then LEDs 1- 4 correspond to that code

activating outputs 1 - 4 respectively. (See programming the LED keypads on page 8.)

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 79 80

Comentarios a estos manuales

Sin comentarios

CADDX NX-8e Especificaciones Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad CADDX NX-8e