CADDX Ranger 9000E Manual de usuario descargar pdf (Pagina 2)

Step 5: Attach the phone cords

Attach the phone cord to the uControl hub

a. Locate the phone cord that you disconnected from

the alarm box telephone jack in Step 1.

b. Plug the phone cord into the gray ALARM PHONE port

on the uControl hub.

Attach the blue cord to the phone jack in the

alarm box

a. Locate the blue cord from the uControl package. This cable

connects the uControl Link to the alarm telephone jack.

b. Take one end of the blue uControl cord (it does not matter

which end) and insert the plug into the telephone jack inside

the alarm box.

Attach the blue cord to the uControl hub

a. Take the other end of the blue uControl cord and insert

the plug into the blue HOME PHONE port on the

uControl hub.

Check the status lights

a. If the ALARM PHONE and the HOME PHONE status lights

are green (or flashing green for the HOME PHONE status

light), then proceed to step 6.

If the ALARM PHONE and HOME PHONE status

lights are not green, see “Troubleshooting

the telephone connection” on page 17 in the

uControl Help Guide.

The HOME PHONE status light will not turn on

if you do not have telephone service.

Step 6: Connect to your home network (wired or wireless)

If Ethernet is available and you are able to connect the uControl Link to your home computer

network, follow the instructions in Step 6. If you do not want to connect to a wired network

(or if you do not have a home network), you can skip this step and proceed to Step7.

Wireless setup takes place online after you complete the uControl Link installation. If you

plan to connect to a wireless network, proceed to Step7.

Do you have an Ethernet port nearby

a. Check the area near the alarm box to see if there is an Ethernet port nearby.

b. If you do not have an existing Ethernet port, check the area for the closest router.

If your home network does not include an Ethernet port near your alarm

box, you might need to locate the closest router. If you do not have an

Ethernet port or router available, skip to step 7.

Attach the white Ethernet cable to your computer network

a. Locate the white Ethernet cable from the uControl package.

b. If you have an Ethernet port near your uControl Link, plug the white uControl Ethernet

cable into the Ethernet port.

c. If you do not have an Ethernet port near your uControl Link, plug the white Ethernet

cable into the nearest router.

Attach the white Ethernet cable to the uControl Link

a. Plug the other end of the white Ethernet cable into the ETHERNET port on the

uControl Link.

If the nearest Ethernet port (or router) is a significant distance

from the uControl Link, you might need to purchase additional

Ethernet cable or have it professionally installed.

Check the Ethernet status light

a. If the ETHERNET status light on the uControl Link is green (or flashing

green), then proceed to step 7.

The ETHERNET status light can take a few minutes to turn

green. If the ETHERNET light does not turn on, see

“Troubleshooting the Ethernet connection” on page 17 in the

uControl Help Guide.

Step 7: Connect the battery wires and uControl hub

Connect the battery wires to the battery terminals

a. Locate the battery (or batteries) that you removed from the alarm box in

step 1.

b. Place the battery back inside the alarm box with the terminals on the

outside.

c. Find the two battery wires you disconnected in Step 1.

d. Connect the red battery connector to the positive terminal (marked by a

+ symbol or red) on the battery.

e. Connect the black battery connector to the negative terminal (marked

by a - symbol or black) on the battery.

If your keypad is showing a LOW BATTERY message, it will

not clear immediately after plugging in the battery. This

message might take several hours to clear.

Attach the uControl hub to the alarm box

a. Find a place inside the alarm box to mount the uControl hub.

The mounting position for the uControl hub must be

inside the alarm box.

You might need to move some of the alarm box wires out

of the way. Be careful when you move the wires to avoid

accidentally disconnecting any of the existing wiring.

b. On the back of the uControl hub, remove the protective film from the

tape and press the uControl hub against the back panel of the alarm

box.

Check the connections

a. After you attach the uControl hub to the alarm box, verify that the

power, keypad, and telephone wires are connected.

Verify that the appropriate power, keypad, telephone,

and Ethernet status lights are green.

uControlHub

HOME PHONE POWER

CONNECT TO

uControlLink

ALARM PHONE KEYPAD

uControlLink

REAL-TIME SECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uControlHub

HOME PHONE POWER

CONNECT TO

uControlLink

ALARM PHONE KEYPAD

uControlLink

REAL-TIME SECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uControlHub

HOME PHONE POWER

CONNECT TO

uControlLink

ALARM PHONE KEYPAD

uControlLink

REAL-TIME SECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

lLink

ECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uControl

ETHERNET

AUX PWR TESTSD CARD SLOT

USB 1

USB 2

Link

CURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uControlHub

HOME PHONE POWER

CONNECT TO

uControlLink

ALARM PHONE KEYPAD

uControlLink

REAL-TIME SECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uControlLink

REAL-TIME SECURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

uContro

Link

REAL-TIME SE

RIT

KEYPADKEYPAD

ALAR

MEH

PHON

ETHERNETETHERNET

I-

WIRELE

ELLULA

WIRELE

ERVICE

TATU

RPO

uControlHub

HOME PHONE POWER

CONNECT TO

uControlLink

ALARM PHONE KEYPAD

Link

CURITY

KEYPAD

ALARM

PHONE

HOME

PHONE

ETHERNET

WI-FI

WIRELESS

CELLULAR

WIRELESS

SERVICE

STATUS

POWER

Step 8: Write down zone map

Your alarm system defines Zones based on the physical features of your home. For example, Zone 1 on

your security system might be associated with your front door. If your security system is armed and you

open the front door, this action triggers a security event in Zone 1.

Before you close the alarm box, you need to write down any zone information that might be written on

the inside of the alarm box door. This information might also be written on the inside cover of your

keypad.

Write down your security zone information

a. In the zone map table below, write the zone mappings in the table. You will use the

information in this table to complete the online account setup.

Step 9: Close the alarm box and activate your account

Close your alarm box

a. If you have a lock on your alarm box, use your key to lock the alarm box

door.

b. If you have screws on your alarm box door, insert the screws and use a

screwdriver to tighten the screws to secure the alarm box door.

c. Check the status lights on the uControl Link to verify that all connections

are good.

If you have the telephone line and an Ethernet line

connected, the status lights for both of these connections

should be green.

Note: The HOME PHONE status light will not turn on if you

do not have telephone service.

d. If any of the lights remain solid red or solid orange, this indicates that

there is a problem of some type with your connection in the indicated

area. To fix the problem, see the related Troubleshooting section of the

uControl Help Guide for the connection that failed.

The SERVICE STATUS light will light up after you activate

your account online.

e. Check the alarm keypad to verify that it is powered and responding to

arm/disarm commands.

Congratulations! You completed the hardware setup.

Access the uControl web site

Now you are ready to access the uControl web site to activate and set up your user account. Go online

and type the following web address in the address field:

You will need the following information to activate your account:

• Zone map information you wrote down in Step 8.

• Shipping manifest or a copy of your welcome email.

• The email address you provided to uControl when you signed up for the service.

Your zone map

Zone number House location

http://www.ucontrol.com/

activate

Supported Models

Ademco and First Alert (FA)

VIA-30P, VISTA 128FB, VISTA 250FBP, 4153, 5110XM, 5140XM, FA1300C, FA1600C, FA1660C, FA2000C, VIA-16, VISTA 20HWSE, VIA-30PSE, VISTA 20HW, VISTA

100, 4130XM, VIA-30, VISTA 128FBP, FA160C, FA1220CV, FA110C, FA1200C, 4140XMP, FA142C, FA120C, FA162C, VISTA 50P, 4110DL, APEX DESTINY 6100,

4120XM, VISTA 20PSIA, VISTA 40, FA168C, 4110XM, 4140XM, VISTA 20SE, VISTA 15P, VISTA 10SE, VISTA 15, VISTA 20, VISTA 10P, FA148CP, VISTA 20P, VISTA 10,

ADT

Focus 128, Focus 75, Focus D32, Focus D50, Safewatch Pro, Safewatch Pro 2000, Safewatch Pro 3000, Safewatch Pro 3000EN

DSC

Partner P-48 (1555), Power 632 (1555MX), PC1565, PC1616, PC1832, PC1864, PC4010, PC4020CF, PC5015 (Power 832 also), PC4000, Power 432 (580), PC4020,

Power 864 (5020), PC1575, Power 832 (5010), Power 632 (1555)

FBI

XL-2P, XL-3, XL-4, XL-5, XL-20, OMNI 624, XL-2T

GE CADDX

NX8E, NX8E CF, Ranger 9000E, Ranger 9000, Ranger 8980E, Ranger 8600E, NX4, NX8, NX6

GE ITI

ADVENT, CONCORD EXPRESS, CONCORD

Moose

Z1200, Z1250, Z2000

Napco

GEM-P801, GEM-P1632, GEM-P800, XP-400, GEM-P9600, MA-3000, GEM-P816, XP-600, GEM-P3200

Radionics

D4412, D6412

Sentrol

ZX400

Go to the next step

)

Go to the next step

)

Go to step 8

Go to the next step

)

NOTES

1 2

Comentarios a estos manuales

Sin comentarios

CADDX Ranger 9000E Manual de usuario Pagina 2

Comentarios a estos manuales